Metal powder coating in Tallinn and Harju County

Metal powder coating and finishing of metal products and surfaces in Tallinn and Harju County (workshop in Vatsla, 5 min from Õismäe) from single parts to production batches (internal oven dimensions 6.5 × 1.6 × 2.1 m). On-site metal surface preparation — sandblasting and zinc priming based on part condition and operating environment.

Powder coating service — JS Production OÜ
TECHNOLOGY

Powder coating process

Every order begins with an assessment of the part's surface condition. Depending on metal cleanliness and operating environment, the part goes through the required preparation and coating stages:

1

Inspection & sandblasting

We inspect the part's surface. If rust, mill scale, or old paint is present, we sandblast it to clean metal and create an anchor profile.

2

Degreasing and cleaning

We remove abrasive dust, oils, and grease residues so the primer and powder coat bond evenly and firmly to the metal.

3

Zinc priming

For steel parts exposed to outdoor weather or moisture, we apply a zinc-rich powder primer before the topcoat to prevent under-film corrosion.

4

Powder application

We electrostatically spray the selected RAL shade and finish onto the grounded metal part, evenly covering edges, welds, and inner corners.

5

Curing at 190–210°C and inspection

The part is cured in our oven at 190–210°C until the powder melts and cross-links into a durable coat. Once cooled, we visually inspect the finish and wrap the parts.

ADVANTAGES & QUALITY

Why choose powder coating over liquid paint?

Powder coating gives a more durable and eco-friendly finish than traditional liquid painting:

Impact & wear resistance

Polymer coating is flexible and resistant to mechanical impacts, scratches, and stone chips.

Even coat without drips

Electrostatic spray evenly covers complex shapes, welds, and sharp edges without drip marks.

Weather & UV resistance

The coating withstands sunlight, temperature changes, rain, snow and road salt well.

Eco-friendly & safe

The paint contains no organic solvents (VOCs) and has no unpleasant odor after curing.

MATERIALS

Metals and surfaces we coat

We powder coat all electrically conductive metals capable of withstanding 190–210°C curing:

Carbon steel
Beams, frames, sheet
Aluminium
Profiles, rims, covers
Galvanized steel
Posts, fences, gates
Stainless steel
Railings, custom parts
Cast iron
Engine parts, housings
PREPARATION & ORDERING

Preparing parts for powder coating

A durable finish starts with proper surface preparation. Below are practical guidelines on how to bring parts in, when sandblasting or zinc priming is needed, and what information to include when requesting a quote:

In what condition should parts be brought in?

Because curing takes place at 190–210°C, all heat-sensitive components must be removed beforehand: rubber bushings, seals, bearings, plastic caps, tire valves, and wiring. Parts must also be free of standard automotive body filler, silicone, and heavy grease. Please point out any threads or bearing seats that need to remain uncoated.

When are sandblasting and zinc primer needed?

Not every part requires every operation—treatment depends on material, current condition, and operating environment. New, clean steel for dry indoor use (such as loft furniture frames or shelving) usually needs only degreasing and a single powder coat. Parts with rust, mill scale, or old paint must first be sandblasted. Steel items used outdoors (gates, railings, rims, suspension parts) receive a zinc-rich powder primer before the topcoat.

What should I include in a quote request?

For an accurate quote, please share: part dimensions (oven internal size: 6.5 m long × 1.6 m wide × 2.1 m high) and approximate weight, material (carbon steel, aluminum, galvanized steel), current surface state (new metal, rust, or old paint), quantity, desired RAL code and finish (matte, gloss, fine texture), and whether the part will be used indoors or outdoors. Attaching a photo or drawing helps speed up the estimate.

PRICING FACTORS

What determines the cost of powder coating?

We price work per item or square meter according to the work involved. The final cost depends on four main factors:

Dimensions & geometry

Our oven's internal dimensions are 6.5 m long, 1.6 m wide, and 2.1 m high (190–210°C). We factor in surface area, weight, and profile complexity: flat sheet panels require less handling and spraying time than complex lattice frames or heavy beams.

Surface condition

Clean new metal requires only degreasing before coating. If the part has rust, mill scale, or old paint, sandblasting is added (metal structures and parts: 70.00 € / hour).

Coating system

Indoor parts need a single topcoat. For outdoor items, we recommend a two-coat system of zinc primer and RAL powder coat, with an additional protective clear coat for rims.

Order volume & batch size

When coating a batch of identical parts in the same RAL color, line setup, hanging, and oven cycle costs are spread across the series.

COLORS

RAL colors

We offer a wide range of standard and special RAL colors with matte, semi-gloss, gloss, fine-textured and textured finishes.

RAL 9005 Jet black
RAL 7016 Anthracite grey
RAL 9016 Traffic white
RAL 7040 Window grey
RAL 3020 Traffic red
RAL 6005 Moss green
RAL 8017 Chocolate brown
RAL 9006 White aluminium
FAQ

Frequently asked questions about powder coating

Answers to common questions regarding powder coating process, turnaround, and pricing:

All electrically conductive metals capable of withstanding 190–210°C can be powder coated: carbon steel, aluminum, stainless steel, galvanized surfaces, and cast iron.

Yes. For lasting adhesion, powder coat cannot be applied over rust, mill scale or loose old paint. We sandblast these parts down to clean metal on site. New, clean metal parts only need degreasing before coating.

Lifespan depends on surface preparation, the coating system (for example, zinc primer plus powder coat) and operating conditions. With proper preparation, powder coating holds up well outdoors; we can give a more specific estimate for your part and its location.

A gloss finish is smooth, reflective, and easy to wipe clean. Smooth matte or semi-gloss gives a subtle, understated look. Fine-textured and textured finishes have a grained feel that hides minor metal imperfections and weld grinding marks while offering higher scratch resistance in daily use (popular for loft furniture, railings, and gates).

The internal dimensions of our curing oven are 6.5 m long, 1.6 m wide, and 2.1 m high (6.5 × 1.6 × 2.1 m). However, whether a part fits depends on all three dimensions together, the geometry of the item, and how it can be hung or positioned inside the chamber—not on length alone. For frames, stair stringers, or complex structures, we recommend sending dimensions or drawings in advance to confirm fit.

The cost of powder coating depends on part dimensions, weight, and quantity, surface condition, and the chosen coating system. If the metal has rust, mill scale, or old paint, sandblasting preparation is added (metal structures and parts at 70.00 € / hour). For outdoor steel parts, a two-coat system with zinc primer and RAL powder coat also affects the price. View base rates in our price list or send a quote request for an exact calculation.

Yes, we offer a wide selection of RAL shades along with different surface finishes: matte, semi-gloss, gloss, fine-textured, and textured. We can help you choose the right combination depending on whether the part is for indoor or outdoor use and the desired look. Availability of a specific RAL shade and finish in stock is confirmed when placing the order.

For an accurate quote, please include the part dimensions and approximate weight, material (carbon steel, aluminum, galvanized steel, stainless steel, or cast iron), current surface condition (new metal, rust, or old paint), quantity, desired RAL shade and surface finish, and whether the parts will be used indoors or outdoors. Attaching a photo or technical drawing is also very helpful.
PRICE QUOTE

Need a Powder Coating Price Quote?

Send us part dimensions, drawings, or quantities with desired RAL color. We will provide a customized quote within 1–2 hours!